From Swatch to Bulk: Where Knit Fabric Orders Usually Go Wrong, and How to Catch It Early
By Chêne Textile Journal4 min read

Most fabric problems do not begin in bulk production. They begin earlier, at the point where someone approves a sample without being sure what was approved. The good news is that almost everything below can be caught with a few cheap steps in the right order.
The usual stages
Different mills use different words, but the path generally looks like this.
- Swatch or hanger. A small piece, often A4 size, to judge hand, look and weight. It is a first impression and nothing more.
- Lab dip. If you need a specific colour, the mill dyes a small test piece to match your reference, a Pantone chip or a physical swatch. You approve it, or ask for another round.
- Strike-off, for prints. A test print on the actual fabric.
- Sample yardage. Enough cloth to cut a proper fit or pre-production sample. This is where you learn how the fabric sews, washes and behaves on a body.
- Bulk. The production run, with an approved standard to compare against.
Skipping stage 4 to save time is the single most common false economy we see.
Where things drift
The swatch was a different batch. Hangers are often cut from development runs, which can be made on different machines, with a different yarn lot, finished more carefully than production will be. Ask whether bulk will be produced the same way, and ask for a swatch cut from a production roll when you can.
Shade varies roll to roll. In dyed knit fabric, small shade differences between lots, and sometimes within a lot, are a fact of life. What matters is the limit you accept and how it is checked. Ask for the colour to be assessed against your approved standard under a defined light source, and ask how rolls from different dye batches will be sorted so that a single garment, or at least a single production lot, is cut from rolls that match.
Shrinkage, after washing. Knits relax in the wash. Ask for dimensional change results from testing on your fabric, and check them against your pattern allowances before cutting. A common method is AATCC 135 or an ISO equivalent; whichever the mill uses, make sure it matches your own market's expectations.
Skew, or spirality. In some knit fabrics the loops lean to one side, and after washing the side seam of a tee twists around the body. It is largely a finishing and construction issue, and it is much easier to prevent than to fix. Wash a sample, then lay the garment flat and see where the side seams end up.
Width and weight. Bulk can come in a few centimetres or grams away from the sample. Settle the acceptable range before you order and write it in.
Pilling and handfeel. A fabric can feel lovely when it is new and pill after a few wears. Ask for pilling data, such as a Martindale result, and rub a sample against itself to see how it behaves.
What belongs in the order
The purchase order is where your approvals become binding. At the least, it should include:
- the fabric reference or code, and the approved standard (a signed and dated sample both sides keep);
- composition, gsm and cuttable width, with tolerances;
- colour references and the approved lab dip;
- the test items you expect and the standard you want them reported against, such as shrinkage, colourfastness and pilling;
- packing and labelling requirements;
- how the parties handle claims for fabric that falls outside the agreed range.
None of this has to be long. A one-page order that says what was approved is worth more than a long document that does not.
About minimum quantities
Minimum order quantities vary widely between fabrics, between mills and between stock and made-to-order cloth. Many brands are surprised to find the minimum is set per colour, not per order. So ask these early:
- Is the minimum per colour, per fabric, or per order?
- Is there a smaller quantity available for a new brand's first run, and what does it cost?
- Is the cloth ready in stock, or does it have to be knitted and dyed from scratch? That changes the lead time more than anything else.
Do not take a lead time on trust. Ask what each step takes, from yarn to knit to dyeing and finishing, and keep a buffer for approval rounds, which are normally where schedules slip.
A habit that pays off
Keep a simple record for every fabric you approve: a swatch, a dated note, the test results and the contact who signed off. When bulk arrives, cut a piece and compare it with the file before anything goes into the cutting room. The brands that do this rarely have a long argument later, because everyone knows what was agreed.
If you are starting with a new supplier, begin with a small trial order of one or two fabrics. You will learn more about how they communicate, and how consistent their output is, from that than from any amount of email.
Explore the collections
Browse our five knit collections, or ask for swatches.


