成恩科纺 CHENGEN TEXTILE

Journal

A Knit Fabric Spec Sheet, Line by Line: GSM, Width, Yarn Count and What They Don't Tell You

By Chêne Textile Journal4 min read

A white European man and woman in earth-toned knit sweaters in a bright gallery space

A fabric card tells you a lot, and it can still leave out the thing you needed to know. Most of the disputes we hear about between brands and mills start with a spec line that both sides read differently. Here is how to read each line, and what to double-check.

GSM: weight, but not the whole story

GSM means grams per square metre. It is the standard way to talk about knit weight, and it tells you roughly how much fibre is in a square metre of cloth. Some markets and some brands talk in ounces per square yard instead, so make sure you know which one is on the sheet.

As a rough working guide, not a rule:

WeightTypical feelOften used for
Under about 140 gsmLight, fluid, can be see-through in pale coloursSummer tops, slips, linings, light dresses
About 140–200 gsmThe everyday rangeT-shirts, polos, casual dresses, pyjamas
Over about 200 gsmSubstantial, warmer, more structureSweatshirts, cardigans, winter knits, trousers

What GSM does not tell you is how the fabric feels. Two jerseys can both be 180 gsm and be completely different cloths, one a tight, fine-gauge cotton and the other an open, hairy linen. Weight tells you how much fibre. The yarn, the gauge and the finishing tell you what it does.

One more practical point: ask whether the figure is measured after finishing, and what tolerance applies. A swatch quoted at 180 gsm that arrives at 165 in bulk will feel and drape differently, and a few percent in either direction is normal, but the allowed range should be written down.

Width: full width versus cuttable width

Knit fabric is often sold on a full-width figure, such as 160 cm. The width you can actually lay a marker on is smaller, because the selvedge edges and any finishing marks have to be trimmed off. For tubular knits there can also be fold lines to avoid.

If your costing depends on fabric consumption, always ask for the cuttable width. A difference of 3–5 cm sounds small and adds up over thousands of metres.

Yarn count: three systems, one headache

You will see different notations on the same page, because different fibres grew up with different counting systems.

  • English cotton count (Ne, or just "S"), as in 30S or 40S. A higher number means a finer yarn. A 30S cotton is a common tee weight, and 60S is much finer.
  • Metric count (Nm), widely used for wool, as in 60Nm/2 or 2/48Nm. Again higher means finer. The "/2" or "2/" tells you it is a two-ply yarn, two strands twisted together, which is stronger and more even.
  • Denier (D), used for filament yarns like silk, as in 20/22D. Here the logic flips: a higher denier is a thicker filament. The "×3" or "×4" tells you how many ends are combined.

The point is not to memorise conversions. It is to avoid comparing a 30S with a 60Nm and thinking you know which is finer. Ask the mill to explain the count in the system you are used to, and ask whether the yarn is single or plied.

Structure: the part that changes the garment

The same yarn in a different structure becomes a different product.

  • Single jersey. One layer of loops, smooth on the face, a little textured on the back. Light and drapey, curls at the edges when cut, and has stretch mostly across the width.
  • 1×1 rib. Alternating knit and purl columns. Pulls in, stretches a lot widthways, and recovers well, so it is the standard for fitted tops, cuffs and necklines.
  • Interlock. Two interlocked layers, smooth on both sides. Heavier and more stable than single jersey, and it does not curl, so it is easier to cut and sew.
  • Piqué. A textured, honeycomb-like surface. Think polo shirts. Good airflow and a bit of body.

If a sheet gives you the fibre and the gsm but not the structure, you have two-thirds of the story.

The lines people skip

Stretch and recovery, shrinkage after washing, colourfastness, pilling resistance and skew (the diagonal twist that pulls side seams around the body in a finished garment) all affect how a garment performs, and none of them is covered by gsm. Standard test methods exist for most of these, including ISO 105 for colourfastness and ISO 12945 for pilling, and a good supplier will tell you which one they used. If a sheet says nothing about testing, ask.

Questions worth sending before the first order

  1. Is the weight measured after finishing, and what is the tolerance?
  2. What is the cuttable width?
  3. Are the yarn counts single or plied, and in which system?
  4. What is the structure, and is there elastane in it?
  5. What shrinkage and colourfastness results do you have for this exact cloth?
  6. Can I have a swatch from a production roll, not just a hanger sample?

A spec sheet is a starting point for the conversation. The brands that get the best fabric are usually the ones that read it closely, then ask the next question.

Fabrics that go with this article

Sample fabrics from our library that match the fibres and uses discussed above.

Request swatches Browse the fabric library

More reading

Chat with us